Now the Position: Home > Products > T8 Diffuse LED Tube > body
Diffuse Lighting 4FT 19W LED Light Tube T8

Diffuse Lighting 4FT 19W LED Light Tube T8

  • Model Number:
  • SYH-T08-012-100C-F08
  • Power:
  • 19W
  • Size:
  • D26*1200MM
  • Input Voltage:
  • AC100-240V
  • Material:
  • Alloy Aluminum housing & PC Cover
  • Color Temperature:
  • 6000-6500K

Diffuse Lighting 4FT 19W LED Light Tube T8

General Introduction

Diffuse Lighting LED Light Tube T8 uses SMD LED2835 LED as light source and there are 600mm(2ft), 900mm(3ft), 1200mm(4ft), and 1500mm(5ft) available.This type Diffuse Lighting LED Light Tube T8 adopts standard G13 socket and work with AC100-240V voltage input and DC72-80V output.


LED Light Tube T8 Details Photo

t8 led tube 4ft led light smd led2835

t8 led tube 4ft led light isolated power supply

t8 led tube 4ft led light milky pc cover

t8 led tube light alloyed aluminum housing

t8 led tube light round end caps

t8 led tube wires

LED Light Tube T8 Features

Diffuse Lighting 4FT 19W LED Light Tube T8 round caps design.

Frosted Cover outside buckled into the alloyed aluminum housing.

Diffused alloyed aluminum housing with higher light emitting efficiency.

Non-isolated power supply with lower impedance and higher conversion efficiency.

International Standard lamp accessories: connectors, clips, screws, power casing,

insulated lead, etc.

LED Light Tube T8

LED light tube T8 can be applied in indoor lighting and outdoor lighting, places such as office, factory, park lot, metro, etc.

t8 led tube application


LED Light Tube T8 Size

t8 led tube 4ft led light size

A

C

---

Minimum

Maximum

Minimum

Maximum

Caps

1197mm

1198mm

1213mm

1214mm

12.7mm



LED Light Tube T8 Parameters

Model NO.

SYH-T08-012-100C-F08

Optical Parameters

Light Source

SMD LED2835

Luminous Flux(lm)

1800

CCT(K)

6000-6500

CRI(Ra)

80

Beam Angle

120°-160°

Light Attenuation ratio (%)

Less than 10% in 3 years

LED Quantity

100


Electrical Parameters

Input Voltage(V)

AC100-240V

Frequency(Hz)

50/60HZ

Output Voltage(V)

DC72-80V

Total Power(W)

19


Power Factor

>0.9

Lifespan (Hrs)

>50,000

Dielectric Voltage Withstand Test

3750Vac/60s

Structural Parameters

Material

Aluminum housing &PC cover

Size(mm)

Φ26×1200

Length(mm)

1200

Net Weight(g)

320


Integrated Parameters

Operating Temperature

-10°-40°

Storage Humidity

-40°-85°

Safety Requirement

/

Environmental Directives

RoHS


LED Light Tube T8 Installation

LED Light Tube T8 Wiring Diagram:

t8 led tube wiring diagram

1) Please turn off electric power before LED Tube Lights installation

2) For refitting old fluorescent lamp, with a two-side-power-input LED tube, please re-connect your wire as the following diagram

t8 led tube installation diagram

3) For diagram A1 loop with inductive ballast & starter, after removing the starter, LED tube can be installed directly into the G13 base. Then LED tube light is ready to work. And the loop has been changed from A1 to A2.

Note: You can just keep the inductive ballast as it was. However, it’ll consumer some power. For saving energy, it’s still suggested to cut it out if your labor cost is not so high.

4) For diagram B1 loop with electronic ballast , please remove the electronic ballast first. Then connect L and N to the two sockets of the G13 base separately. Now your LED tube light is ready to be turned on. And the loop has been changed into the one showed in diagram B2.

LED Light Tube T8 Package

LED light tube package

Concentrated on LED Tubes

Specialized in production, R&D, design and sales on various types of LED tubes only for more than 5 years, Syhdee has already won trust and favor from customers at home and abroad. Syhdee LED tubes were widely applied in lighting retrofit replacement project, commercial lighting, industry lighting, office lighting, architecture lighting, etc.

Production Capability

With a 30,000 square meter workshop equipped with advanced machines and over 520 skilled workers, our production capability has reached up to 1500000 pieces of LED tube lights per month.

R&D Strength

Professional R&D team to guarantee the stable performance of products:

Chip & Packaging Team

lluminating Efficiency Team

Electrical Engineering Team

Electronic Engineering Team

Hardware Structure Team

Industrial Design Team

Product Quality

Syhdee Manufactory has passed Germany TUV Rheinland and DEKRA Quality Management System certification.

Syhdee LED tubes complied with VDE,TUV, UL, FCC, DLC, SAA, C-Tick, CE&RoHS, Erp, PSE directives, etc.

Factory Direct Price

We are the manufacturer of LED tubes, which enables us to offer our customers factory direct price. Meanwhile good relationship with our material suppliers, skilled staff and advanced facilities make it possible for us to quote the most competitive price.

LED Tube OEM&ODM Project

As one professional LED tube supplier in China, we can offer the turnkey LED tube solutions for our customers. OEM&ODM project is well available.

Send us a message
My status